http://cafe.naver.com/tsinside/162 퍼온글 입니다.
http://cafe.naver.com/tsinside/162 퍼온글 입니다.
1. config 예제
¨ /c/sys/http enable
: Web 접속 기능을 활성화 시킴
>> Main# /c/sys/http e
Current HTTP access: enabled
New HTTP access: enabled
¨ /c/sys/user/usrpw
: user mode password를 설정 한다(config 불가)
>> User Access Control# usrpw
Changing USER password; validation required...
Enter current administrator password:
Enter new user password:
Re-enter new user password:
New user password accepted.
¨ /c/snmp/name
: system name을 설정 한다
>> L4-05 - Main# c/snmp/name
Current SNMP "sysName":
"L4-05"
Enter new "sysName", without quotes:
kyj
>> kyj - SNMP#
¨ /c/sys/user/admpw
: admin mode password를 설정 한다
>> Main# /c/sys/user/admpw
Changing ADMINISTRATOR password; validation required...
Enter current administrator password:
Enter new administrator password:
¨ /c/port 8/fast/speed 100/mode full/auto off
: port 8을 speed 100Mbps, full duplex로 지정(auto negotiation은 off됨)
(적용에 걸리는 시간은 3초 이내이며 링크는 잠깐 끊어 진다)
>> Main# /c/port 8/fast/speed 100/mode full/auto off
Current port 8 speed setting: 10/100
Pending new speed setting: 100
Current port 8 mode setting: any
Pending new mode setting: full duplex
Current port 8 autonegotiation: on
Pending new autonegotiation: off
¨ /c/vlan 11/ena
: vlan을(vlan11) 생성한다
>> Main# /c/vlan 11/ena
Current status: enabled
New status: enabled
¨ /c/vlan 11/add 8
: vlan에 port를 할당한다
>> Main# /c/vlan 11/add 8
Port 8 is an UNTAGGED port and its current PVID is 1.
Confirm changing PVID from 1 to 11 [y/n]: y
Current ports for VLAN 11: 1
Pending new ports for VLAN 11: 1 8 è port1,port8 을 의미
¨ /c/snmp/rcomm goguma/trap1 10.55.1.49
: snmp server와 권한을 설정
>> Main# /c/snmp/rcomm goguma/trap1 10.55.1.49
Current SNMP read community string: "goguma"
Pending new read community string: "goguma"
Current first SNMP trap host address: 10.55.1.49
New pending first SNMP trap host address: 10.55.1.49
¨ /c/ip/if 11/ena/addr 2.2.2.2/mask 255.255.255.0/broad 2.2.2.255/vlan 11
: interface 11을 만들고 interface 11에 address와 vlan을 할당한다
>> Main# /c/ip/if 11/ena/addr 2.2.2.2/mask 255.0.0.0/broad 2.255.255.255/vlan 11
Current status: enabled
New status: enabled
Current IP address: 10.88.10.2
New pending IP address: 2.2.2.2
Switch is set to use BOOTP for IP address assignment.
Do you want to DISABLE the use of BOOTP? [y/n] n
Use of BOOTP not changed.
Current subnet mask: 255.255.255.0
New pending subnet mask: 255.255.255.0
Current broadcast address: 10.88.10.255
New pending broadcast address: 2.2.2.255
Current VLAN: 11
New pending VLAN: 11
¨ /c/ip/gw 4/ena/addr 3.3.3.3
: gw 4를 생성하고 ip를 부여한다
(Destination에 대한 정보가 없을 경우 gw로 보낸다)
>> Main# /c/ip/gw 4/ena/addr 3.3.3.3
Current status: disabled
New status: enabled
Current IP address: 0.0.0.0
New pending IP address: 3.3.3.3
¨ /c/ip/route/add 1.1.1.1 255.0.0.0 2.2.2.2 11
: static route를 설정(destination:1.1.1.1, nexthop:2.2.2.2, interface: 11)
(여기서 interface는 해당 port가 속한 vlan에 대한 if NO. 임)
* if 생성 순서: vlan 생성 è port를 vlan에 할당 è if를 만들고 ip address와 vlan을 할당
>> Main# /c/ip/route/add 1.1.1.1 255.0.0.0 2.2.2.2 11
Enter destination IP address: 1.1.1.1
Enter destination subnet mask: 255.0.0.0
Enter gateway IP address: 2.2.2.2
Enter interface number: (1-256) 11
¨ /c/ip/route/rem 1.1.1.1 255.0.0.0 2.2.2.2 11
: static route를 삭제
Enter destination IP address: 1.1.1.1
Enter destination subnet mask: 255.0.0.0
Enter gateway IP address: 2.2.2.2
Enter interface number: (1-256) 11
¨ /c/vr 53/ena/vrid 53/if 11/prio 110/addr 3.3.3.3
: vrrp 53을 enable시키고 address는 3.3.3.3 (interface 11에 해당)priority는 110
>> Main# /c/vrrp/vr 53/ena/vrid 53/if 11/prio 110/addr 3.3.3.3
Current status: disabled
New status: enabled
Current virtual router ID: 1
New pending virtual router ID: 53
Current interface number: 1
New pending interface number: 11
Current router priority: 100
New pending router priority: 110
Current IP address: 0.0.0.0
New pending IP address: 3.3.3.3
¨ /c/sys/ntp/on/server 10.55.1.49
: ntp server를 설정 한다
>> Main# /c/sys/ntp/on/server 10.55.1.49
Current status: OFF
New status: ON
Current NTP server address: 0.0.0.0
New pending NTP server address: 10.55.1.49
¨ /c/slb/on
: slb를 활성화 시킨다
>> Main# /c/slb/on
Current status: OFF
New status: ON
¨ /c/slb/real 16/ena
: real server 16을 활성화 시킨다
>> Main# /c/slb/real 16/ena
Current status: disabled
New status: enabled
¨ /c/slb/group 1/metric hash
: slb를 적용할 group을 지정하고 slb방식 지정
>> Main# /c/slb/group 1/metric hash
Current metric: leastconns
New pending metric: hash
¨ /c/slb/group 1/add 1
: slb를 적용할 real server 1을 group1에 할당 한다
>> Main# /c/slb/group 1/add 1
Real server 1 added to real server group 1.
¨ /c/slb/group 1/rem 1
: slb정책에서 server 1을 삭제 한다
>> Main# c/slb/group 1/rem 1
Real server 1 removed from real server group 1.
¨ /c/slb/real 16/dis
: real server 16을 비활성화 시킨다
>> Main# /c/slb/real 16/dis
Current status: disabled
New status: disabled
¨ /c/slb/filt 22/ena/action deny/dip 2.2.2.2/dmask 255.0.0.0
: filter를 적용한다(destination이 2.2.2.2인 packet은 deny한다)
>> Main# /c/slb/filt 22/ena/action deny/dip 2.2.2.2/dmask 255.0.0.0
Current status: disabled
New status: enabled
Current action: allow
Pending new action: deny
Current destination address: any
New pending destination address: 2.2.2.2
Current destination mask: 0.0.0.0
New pending destination mask: 255.0.0.0
¨ /c/slb/port 2/add 22
: port 2에 filter 22를 적용 한다
>> Main# /c/slb/port 2/add 22
Filter 22 added to port 2.
¨ /c/slb/port 1/client enable
: port 1을 slb의 client측으로 지정 한다
>> SLB port 1# /c/slb/port 1/client e
Current client processing: disabled
New client processing: enabled
¨ /c/slb/port 2/server enable
: port 2를 slb의 server측으로 지정 한다
>> Main# /c/slb/port 2/server enable
Current server processing: disabled
New server processing: enabled
¨ apply
: RAM에 저장(설장값이 장비에 실제 적용됨)
¨ save
: NVRAM에 저장되며 장비 reboot후에도 config 유지됨
2. Status monitoring 예제
¨ /i/link
: port의 link 상태 정보를 본다
>> Main# /i/link
------------------------------------------------------------------
Port Speed Duplex Flow Ctrl Link
---- ----- -------- --TX-----RX-- ------
1 100* full* yes yes up
2 100* full* yes yes up
3 100* full* yes yes up
4 100* full* yes yes up
5 100* full* yes yes up
6 10 half no no down
7 10/100 any yes yes down
8 10/100 any yes yes down
* value set by configuration; not autonegotiated.
(default는 위의 port 7,8이며 “*”는 user의 port상태 강제 지정을 뜻함
즉, default는 대응 장비와의 auto negonegotiation을 통해 speed와 duplex를 설정 하나
호환성에 문제 소지가 있으므로 port 상태를 강제 지정하는 것이 안정성이 높음)
¨ /i/sys
: system 정보를 본다(http사용여부,snmp,hostname,version,date…)
>> L4-24 - Main# /i/sys
System Information at 16:37:36 Thu Jan 2, 2003
Alteon 184
sysName: L4-24
sysLocation:
Switch is up 23 days, 23 hours, 43 minutes and 37 seconds.
Last boot: 16:53:38 Mon Dec 9, 2002 (watchdog timer)
MAC address: 00:60:cf:4b:4b:80 IP (If 11) address: 10.55.25.1è가장 빠른 if의 ip.
Hardware Revision: B
Hardware Part No: E05_5B-B_6B-A
Software Version 10.0.25 (FLASH image1), active configuration.
¨ /i/vlan
: vlan에 대한 정보를 본다
>> Main# /i/vlan
VLAN Name Status Jumbo Ports
---- -------------------------------- ------ ----- ----------------
1 Default VLAN ena n 6-8
11 VLAN 11 ena n 1
12 VLAN 12 ena n 2
13 VLAN 13 ena n 3
14 VLAN 14 ena n 4
15 VLAN 15 ena n 5
(위의 항목중 Jumbo의 의미는 특정 vlan에서 Jumbo를 enable시킬 경우 vlan에 속한 port에 링크된 장비와 Ethernet의 MTU 보다 큰 frame을 주고 받을 수 있도록 한다)
¨ /i/route/dum
: route 정보를 본다
>> Main# /i/route/dum
Destination Mask Gateway Type Tag Metr If
--------------- --------------- --------------- --------- --------- ---- --
0.0.0.0 0.0.0.0 10.88.10.1 indirect static 11
10.17.0.0 255.255.0.0 10.88.40.100 indirect static 15
10.55.128.0 255.255.255.128 10.88.40.100 indirect static 15
10.55.136.0 255.255.255.0 10.88.40.100 indirect static 15
10.55.146.0 255.255.255.0 10.88.40.100 indirect static 15
10.88.0.0 255.255.255.0 10.88.0.1 direct fixed 12
10.88.0.1 255.255.255.255 10.88.0.1 local addr 12
10.88.0.255 255.255.255.255 10.88.0.255 broadcast broadcast 12
10.88.1.0 255.255.255.0 10.88.1.1 direct fixed 13
10.88.1.1 255.255.255.255 10.88.1.1 local addr 13
10.88.1.255 255.255.255.255 10.88.1.255 broadcast broadcast 13
* Metr If: Gateway에 해당 되는 interface NO.
* indirect: static route, default route의 destination network address
* static: static route, default route의 next-hop
* direct: 설정한 interface의 network address
* fixed, local, addr: 설정한 interface의 ip address
¨ /i/ip
: ip interface에 대한 정보를 본다
>> Main# /i/ip
Interface information:
11: 10.88.10.2, 255.255.255.0, 10.88.10.255, vlan 11, up
12: 10.88.0.1, 255.255.255.0, 10.88.0.255, vlan 12, up
13: 10.88.1.1, 255.255.255.0, 10.88.1.255, vlan 13, up
14: 10.88.2.1, 255.255.255.0, 10.88.2.255, vlan 14, up
<v:group style="Z-INDEX: 251649536; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 9pt; WIDTH: 42.75pt; HEIGHT: 36pt; MARGIN-LEFT: -39.75pt; LEFT: 0px" id=_x0000_s1026 coordsize="855,720" coordorigin="906,9725"><v:line style="POSITION: absolute; flip: x" id=_x0000_s1027 to="1761,10085" from="1221,9725"><v:stroke endarrow="block"></v:stroke></v:line><v:shape style="POSITION: absolute; WIDTH: 720px; HEIGHT: 540px; TOP: 9905px; LEFT: 906px" id=_x0000_s1028 type="#_x0000_t202" stroked="f" filled="f"><v:textbox>
|
if
|
</v:textbox></v:shape></v:group> 15: 10.88.40.1, 255.255.255.0, 10.88.40.255, vlan 15, up
<v:line style="Z-INDEX: 251650560; POSITION: absolute; TEXT-ALIGN: left; LEFT: 0px" id=_x0000_s1029 to="243pt,32.25pt" from="189pt,14.25pt"><v:stroke endarrow="block"></v:stroke></v:line>Default gateway information: metric strict
<v:shape style="Z-INDEX: 251651584; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 1.5pt; WIDTH: 3in; HEIGHT: 61.5pt; MARGIN-LEFT: 240.75pt; LEFT: 0px" id=_x0000_s1030 type="#_x0000_t202" stroked="f" filled="f"></v:shape> 1: 10.88.10.1, up
Current IP forwarding settings: ON, dirbr disabled
Current local networks:
Current IP port settings:
All other ports have forwarding ON
Current RIP settings:
OFF, update 30
split horizon
BGP Information:
OFF, id 0.0.0.0
BGP Peer Information:
<v:shape style="Z-INDEX: 251653632; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 11.25pt; WIDTH: 180pt; HEIGHT: 47.25pt; MARGIN-LEFT: 315pt; LEFT: 0px" id=_x0000_s1032 type="#_x0000_t202" stroked="f" filled="f"></v:shape>¨ /i/slb/sess/find
: 특정 source의 연결 상태를 확인 한다
<v:line style="Z-INDEX: 251654656; POSITION: absolute; TEXT-ALIGN: left; LEFT: 0px; flip: y" id=_x0000_s1033 to="342pt,30.75pt" from="342pt,12.75pt"><v:stroke endarrow="block"></v:stroke></v:line>
<v:oval style="Z-INDEX: 251652608; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 12pt; WIDTH: 36pt; HEIGHT: 27pt; MARGIN-LEFT: 327pt; LEFT: 0px" id=_x0000_s1031 filled="f"></v:oval>>> L4-05 - Main# /i/slb/sess/find 10.55.0.13
1,3: 10.55.0.13 80, 61.72.74.186 10127 -> 211.181.199.81 10127 age 2 E
1,12: 10.55.0.13 80, 211.178.131.232 64745 -> 211.181.199.57 64745 age 4 E
1,16: 10.55.0.13 80, 211.213.0.188 3320 -> 211.181.199.57 3320 age 2
1,24: 10.55.0.13 80, 210.181.105.112 36939 -> 211.181.199.57 36939 age 2 E
1,31: 10.55.0.13 80, 211.243.108.194 2286 -> 211.181.199.57 2286 age 2 E
1,35: 10.55.0.13 80, 211.52.144.212 62597 -> 211.181.199.49 62597 age 4 E
1,39: 10.55.0.13 80, 203.224.93.141 2807 -> 211.181.199.49 2807 age 2 E
1,46: 10.55.0.13 80, 211.38.49.33 42366 -> 211.181.199.81 42366 age 2 E
1,53: 10.55.0.13 80, 211.230.65.133 1448 -> 211.181.199.81 1448 age 4 E
1,58: 10.55.0.13 80, 218.148.17.119 64178 -> 211.181.199.89 64178 age 2 E
1,64: 10.55.0.13 80, 211.183.103.102 1028 -> 211.181.199.81 1028 age 2 E
1,73: 10.55.0.13 80, 61.73.143.75 1127 -> 211.181.199.89 1127 age 2 E
1,88: 10.55.0.13 80, 211.224.178.86 1716 -> 211.181.199.49 1716 age 4 E
1,91: 10.55.0.13 80, 218.51.241.147 32854 -> 211.181.199.49 32854 age 4 E
1,99: 10.55.0.13 80, 220.76.132.45 42916 -> 211.181.199.81 42916 age 2 E
1,101: 10.55.0.13 80, 218.146.42.246 65366 -> 211.181.199.89 65366 age 0
¨ /i/vrrp
: vrrp의 동작 상태를 파악 한다
>> L4-05 - Main# /i/vrrp
VRRP information:
11: vrid 11, 10.55.8.1, if 11, renter, prio 121, master
12: vrid 12, 10.55.9.1, if 12, renter, prio 121, master
13: vrid 13, 10.55.10.1, if 13, renter, prio 121, master
14: vrid 14, 10.55.11.1, if 14, renter, prio 121, master
15: vrid 15, 10.55.12.1, if 15, renter, prio 121, master
16: vrid 16, 10.55.13.1, if 16, renter, prio 121, master
<v:polyline style="Z-INDEX: 251655680; POSITION: absolute; TEXT-ALIGN: left; LEFT: 0px; mso-position-horizontal: absolute; mso-position-vertical: absolute" id=_x0000_s1034 coordsize="360,360" filled="f" points="27pt,14.25pt,27pt,32.25pt,45pt,32.25pt"><v:stroke endarrow="block"></v:stroke><v:path arrowok="t"></v:path></v:polyline> 17: vrid 17, 10.55.14.1, if 17, renter, prio 121, master
<v:shape style="Z-INDEX: 251656704; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 3pt; WIDTH: 6in; HEIGHT: 54pt; MARGIN-LEFT: 43.5pt; LEFT: 0px" id=_x0000_s1035 type="#_x0000_t202" stroked="f" filled="f"></v:shape>
|
Virtual router ID:17, virtual router addresss 10.55.14.1, virtual router가 속한 interface17 Virtual router 17번에 대한 L4-5의 prioryty는 121(default:100) 즉 master로 동작 |
¨ /i/log
: 장비에 쌓인 log를 확인 한다
>> L4-05 - Main# /i/log
Dec 16 14:17:12 NOTICE mgmt: admin login on Console
Dec 16 14:19:25 NOTICE mgmt: admin logout from Console
Dec 16 16:12:20 NOTICE mgmt: admin login on Console
Dec 16 16:26:28 NOTICE mgmt: admin logout from Console
¨ /i/slb/dump
<v:shape style="Z-INDEX: 251659776; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 9.75pt; WIDTH: 2in; HEIGHT: 68.25pt; MARGIN-LEFT: 312pt; LEFT: 0px" id=_x0000_s1038 type="#_x0000_t202" stroked="f" filled="f"></v:shape> : slb와 관련된 모든 정보를 확인 한다
<v:polyline style="Z-INDEX: 251658752; POSITION: absolute; TEXT-ALIGN: left; LEFT: 0px" id=_x0000_s1037 coordsize="540,540" filled="f" points="4in,36pt,4in,9pt,306pt,9pt,315pt,9pt"><v:stroke endarrow="block"></v:stroke><v:path arrowok="t"></v:path></v:polyline>>> L4-05 - Main# /i/slb/dum
Real server state:
<v:oval style="Z-INDEX: 251657728; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 0px; WIDTH: 45pt; HEIGHT: 18pt; MARGIN-LEFT: 264.75pt; LEFT: 0px" id=_x0000_s1036 filled="f"></v:oval> 1: 211.181.199.49, 00:03:ba:05:bc:ce, vlan 11, port 1, health 3, up
2: 211.181.199.57, 00:03:ba:01:4d:4e, vlan 11, port 1, health 3, up
3: 211.181.199.65, 00:00:00:00:00:00, vlan 0, port 0, health 3, FAILED
4: 211.181.199.73, 00:00:00:00:00:00, vlan 0, port 0, health 3, FAILED
5: 211.181.199.81, 00:03:ba:01:4e:74, vlan 12, port 2, health 3, up
6: 211.181.199.89, 00:03:ba:01:4e:45, vlan 12, port 2, health 3, up
7: 211.181.199.97, 00:00:00:00:00:00, vlan 0, port 0, health 3, FAILED
Virtual server state:
<v:shape style="Z-INDEX: 251662848; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 9pt; WIDTH: 261pt; HEIGHT: 45pt; MARGIN-LEFT: 145.5pt; LEFT: 0px" id=_x0000_s1041 type="#_x0000_t202" stroked="f" filled="f"></v:shape>
<v:polyline style="Z-INDEX: 251661824; POSITION: absolute; TEXT-ALIGN: left; LEFT: 0px; mso-position-horizontal: absolute; mso-position-vertical: absolute" id=_x0000_s1040 coordsize="540,360" filled="f" points="123.75pt,30.75pt,123.75pt,12.75pt,150.75pt,12.75pt"><v:stroke endarrow="block"></v:stroke><v:path arrowok="t"></v:path></v:polyline>Redirect filter state:
<v:oval style="Z-INDEX: 251660800; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 12.75pt; WIDTH: 42.75pt; HEIGHT: 27pt; MARGIN-LEFT: 102pt; LEFT: 0px" id=_x0000_s1039 filled="f"></v:oval> 51: action redir
group 1, health 3, backup none, vlan any
proxy enabled, radius snoop disabled
thash auto
real servers:
1: 211.181.199.49, backup none, 0 ms, up
2: 211.181.199.57, backup none, 0 ms, up
3: 211.181.199.65, backup none, 0 ms, FAILED
4: 211.181.199.73, backup none, 0 ms, FAILED
5: 211.181.199.81, backup none, 2 ms, up
6: 211.181.199.89, backup none, 2 ms, up
7: 211.181.199.97, backup none, 0 ms, FAILED
¨ /stats/slb/group 1
: group으로 묶어진 real server들의 상태를 확인(session수)
(아래의 counter를 clear하기 위해서는 장비를 reboot해야 함)
>> L4-05 - Main# /stats/slb/group 1
------------------------------------------------------------------
Real server group 1 stats:
Current Total Highest
Real IP address Sessions Sessions Sessions Octets
---- --------------------------- -------- ---------- -------- ---------------
1 211.181.199.49 3343 154115549 15220 0
2 211.181.199.57 3512 156260229 14830 0
5 211.181.199.81 3353 154525434 14298 0
6 211.181.199.89 3379 159042746 14703 0
---- --------------------------- -------- ---------- -------- ---------------
13587 623943958 59051 0
¨ operation/slb/clear
: session table을 clear 한다(현재 연결된 session들을 끊는다)
>> Main# oper/slb/clear
Session table cleared.
¨ /stats/mp/cpu
: cpu 사용률을 확인 한다
>> L4-05 - Main# /stats/mp/cpu
------------------------------------------------------------------
CPU utilization:
cpuAUtil1Second: 15% cpuBUtil1Second: 14%
cpuAUtil4Seconds: 15% cpuBUtil4Seconds: 14%
cpuAUtil64Seconds: 15% cpuBUtil64Seconds: 14%
¨ /c/dump
: config된 모든 정보를 확인 한다
>> L4-24 - Main# /c/dump
script start "Alteon 184" 4 /**** DO NOT EDIT THIS LINE!
/* Configuration dump taken 17:51:52 Thu Jan 2, 2003
/* Version 10.0.25, Base MAC address 00:60:cf:4b:4b:80
/* L4-24
/c/sys
snmp r
http ena
hprompt ena
/cfg/sys/notice noprompt
--------------- 접 근 경 고 ---------------
부당한 방법으로 전산망에 접속하거나 정보를 삭제, 변경, 유출 하는 자는
관련 지침이나 국가법령에 따라 처벌을 받게 됩니다.
Tel : 769-8957
.
/**** The previous line must be a single '.'
tnet ena
/c/sys/user
admpw "5a35c66312358222937ea7a2d18521d045c12f51951dd4a7f3102aca7f8fc616"
/c/snmp
<v:shapetype id=_x0000_t88 coordsize="21600,21600" filled="f" path="m,qx10800@0l10800@2qy21600@11,10800@3l10800@1qy,21600e" o:spt="88" adj="1800,10800"><v:formulas><v:f eqn="val #0"></v:f><v:f eqn="sum 21600 0 #0"></v:f><v:f eqn="sum #1 0 #0"></v:f><v:f eqn="sum #1 #0 0"></v:f><v:f eqn="prod #0 9598 32768"></v:f><v:f eqn="sum 21600 0 @4"></v:f><v:f eqn="sum 21600 0 #1"></v:f><v:f eqn="min #1 @6"></v:f><v:f eqn="prod @7 1 2"></v:f><v:f eqn="prod #0 2 1"></v:f><v:f eqn="sum 21600 0 @9"></v:f><v:f eqn="val #1"></v:f></v:formulas><v:path o:connecttype="custom" arrowok="t" textboxrect="0,@4,7637,@5" o:connectlocs="0,0;21600,@11;0,21600"></v:path><v:handles><v:h position="center,#0" yrange="0,@8"></v:h><v:h position="bottomRight,#1" yrange="@9,@10"></v:h></v:handles></v:shapetype><v:shape style="Z-INDEX: 251663872; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 4.5pt; WIDTH: 36pt; HEIGHT: 1in; MARGIN-LEFT: 126pt; LEFT: 0px" id=_x0000_s1042 type="#_x0000_t88"></v:shape> name "L4-24"
<v:shape style="Z-INDEX: 251664896; POSITION: absolute; TEXT-ALIGN: left; MARGIN-TOP: 0.75pt; WIDTH: 261pt; HEIGHT: 54pt; MARGIN-LEFT: 161.25pt; LEFT: 0px" id=_x0000_s1043 type="#_x0000_t202" stroked="f" filled="f"></v:shape>
|
Rcomm: read only 권한 t1comm: trap server 1(trap server2도 가능) |
rcomm "goguma"
t1com "goguma"
trap1 10.55.0.49
/c/port 1
pvid 11
/c/port 1/fast
speed 100
fctl both
mode full
auto off
/c/port 2
pvid 12
/c/port 2/fast
speed 100
fctl both èflow control을 나타내며 fast Ethernet은 default 값이다
mode full
auto off
/c/port 3
pvid 13
/c/port 3/fast
speed 100
fctl none
mode full
auto off
/c/port 4
pvid 14
/c/port 4/fast
speed 100
fctl both
mode full
auto off
/c/port 5
pvid 15
/c/port 5/fast
speed 100
fctl both
mode full
auto off
/c/port 6
pvid 12
/c/port 8
pvid 18
/c/port 8/fast
speed 100
fctl both
mode full
auto off
/c/port 9
pvid 19
/c/port 9/fast
speed 100
fctl both
mode full
auto off
/c/vlan 1
def 7
/c/vlan 9
ena
name "VLAN 9"
def 0
/c/vlan 11
ena
name "VLAN 11"
def 1
/c/vlan 12
ena
name "VLAN 12"
def 2 6
/c/vlan 13
ena
name "VLAN 13"
def 3
/c/vlan 14
ena
name "VLAN 14"
def 4
/c/vlan 15
ena
name "VLAN 15"
def 5
/c/vlan 18
ena
name "VLAN 18"
def 8
/c/vlan 19
ena
name "VLAN 19"
def 9
/c/stp 1/off
/c/stp 1/clear
/c/stp 1/add 1 11 12 13 15 18 9 19 14
/c/pmirr/mirror ena
/c/pmirr/monport 7
add 2 both
/c/pmirr/monport 7
add 3 both
/c/ip
rearp 2
metrc strict
/c/ip/if 11
ena
addr 10.55.25.1
mask 255.255.255.0
broad 10.55.25.255
vlan 11
/c/ip/if 12
ena
addr 15.32.37.254
mask 255.255.255.0
broad 15.32.37.255
vlan 12
/c/ip/if 13
ena
addr 15.32.38.254
mask 255.255.255.0
broad 15.32.38.255
vlan 13
/c/ip/if 14
ena
addr 10.88.10.1
mask 255.255.255.0
broad 10.88.10.255
vlan 14
/c/ip/if 15
ena
addr 10.55.14.1
mask 255.255.255.0
broad 10.55.14.255
vlan 15
/c/ip/if 18
ena
addr 10.55.77.1
mask 255.255.255.0
broad 10.55.77.255
vlan 18
/c/ip/if 19
ena
addr 10.55.35.2
mask 255.255.255.0
broad 10.55.35.255
vlan 19
/c/ip/gw 1
ena
addr 10.55.14.100
intr 1
retry 4
arp enabled
/c/ip/route
add 15.32.36.0 255.255.255.0 15.32.37.253 12
add 15.32.35.0 255.255.255.0 15.32.37.253 12
add 223.254.20.0 255.255.255.0 15.32.38.252 13
add 10.55.0.0 255.255.0.0 10.55.25.100 11
add 10.55.16.0 255.255.255.0 10.55.14.100 15
add 10.17.0.0 255.255.0.0 10.55.25.100 11
add 10.88.0.0 255.255.0.0 10.88.10.2 14
add 192.168.104.70 255.255.255.255 10.55.35.1 19
add 128.134.98.0 255.255.255.0 10.55.35.1 19
add 210.124.166.0 255.255.255.0 10.55.35.1 19
add 72.12.202.0 255.255.255.0 15.55.35.1 19
add 72.12.204.0 255.255.255.0 10.55.35.1 19
add 192.168.254.0 255.255.255.0 10.55.35.1 19
add 223.1.1.0 255.255.255.0 10.55.35.1 19
/c/sys/ntp
on
server 10.55.0.205
/
script end /**** DO NOT EDIT THIS LINE!
http://cafe.naver.com/tsinside/162 퍼온글 입니다.
http://cafe.naver.com/tsinside/162 퍼온글 입니다.